Presenting an extravagant shoe stand that will add style to your home. Now drumsticks can be used to store your trainers, high heels and other shoes. With a few tricks and the right DIY tools you can transform the sticks into a stylish shoe arrangement.
What you need
- set square
- tape measure
- Wood glue
- Forstner drill bit (15mm, matches handle diameter of drumsticks)
- Wood drill bit (10mm, matches diameter of drumstick head)
- 1 wooden rod, 1m long (diameter 50mm)
- 20 drumsticks (length 40cm, head diameter 10mm, handle diameter 15mm)
Let's start - step by step
Make out where the drumsticks will go
What you need: Pencil, tape measure, wooden rod, drumsticks
To be able to turn the drumsticks into shoe holders, you are going to need to drill precise holes. For this reason, it is advisable to mark reference lines. To do so, first fix the wooden rod to a workbench. Now mark the centre point on each of the outer cuts edges of the wooden rod. Join the two centre points with a straight line running along the centre of the wooden rod. This reference line divides the wooden rod into two exactly equal halves.
Now fix the wooden rod to a workbench so that the centre line faces exactly upwards. Then mark two more reference lines where the drumsticks will later be fastened. To do so, start from the centre line and mark two more parallel lines, one 5 mm to the right and one 5 mm to the left of the centre line.
On the left-hand reference line, now make a mark every 12 cm for the eight holes you are going to drill later, beginning at a distance of 5 cm from the right-hand outer cut edge of the wooden rod. On the right-hand reference line, now also mark the eight holes each at an interval of 12 cm. Begin here at a distance of 5 cm from the left-hand cut edge of the wooden rod so that the drilled holes on the right-hand side are each offset by 6 cm from the drilled holes on the left-hand side. In the end, the last drilled hole on each reference line is 11 cm from the cuts edges. This way, there will later be eight drumsticks on each side of the centre line.
Drill the holes for the drumsticks
What you need: Cordless drill/driver with matching bit, screw clamps, 10mm wood drill bit, masking tape
The second step is to drill. To do so, fix the wooden rod to a workbench so that the left-hand reference line faces exactly upwards. To ensure that the drumsticks sit securely in the wooden rod despite their narrowing shape, use the tape measure to measure the circumference of the drumstick head (ball-shaped tip) and calculate the diameter before drilling. In this example it is 10 mm. Then identify the position on the drumstick shaft that has the same 10 mm diameter as the head. To ensure maximum stability, the sticks should later be inserted into the wooden rod up to this identified position. This means that the holes have to be drilled to the corresponding depth. To do so, use the tape measure to measure the length from the identified position on the shaft to the drumstick head. When doing so, make absolutely sure that the wooden rod is not drilled through.
Tip: Mark the required drilling depth on the wood drill bit with some masking tape.
Next, use a cordless drill driver and a wood drill bit (10 mm) to drill the previously marked holes to the required depth in the wooden rod. Then fix the wooden rod to a workbench so that the right-hand reference line now faces up and drill the holes marked.
You can use the following formula to calculate the diameter by means of the circumference:
Circumference / PI (approx. 3.142) = diameter
Creating the feet for the shoe stand
What you need: mini-saw, drumsticks
Now you need to give the shoe stand its “legs”. To do this, you will need four more drumsticks which will later be inserted into the bottom of the wooden rod. Fix each of the drumsticks securely to a workbench and shorten them to an overall length of approx. 30 cm beginning from the handle end. The ball-shaped tips will later serve as feet. You can easily shorten the sticks using a mini saw.
What you need: Cordless drill/driver with matching bit, Pencil, tape measure, Forstner drill bit (15mm)
Before you can drill the holes for the shoe stand’s legs on the underside, you should mark reference lines in the same way as in step 1. To ensure a firm footing, the distance of the reference lines from the centre line should be 10 mm . Then mark the holes for two legs on each side, about 5 cm from the edge. Now use the cordless drill driver and a Forstner drill bit (15 mm) to drill the holes vertically into the wooden rod.
Adding the finishing touches
What you need: Wood glue
Last but not least, carefully erase all reference lines and insert the shoe holders and the legs into the holes. If you want, you can put some wood glue on the drumsticks first to give them additional stability. Now attach your brogues, Chucks and other shoes – and your new hallway rockstar is finished!
Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.