With our DIY herb rack, you’ll always have fresh herbs to hand. Whether thyme, basil or mint, your favourite herbs will flourish just above your head. And not only can they be used to season your food, they’ll also fill your kitchen with a delightful, fresh aroma!
What you need
- Wood drill bit (18 mm)
- Drill bits for mounting the rack (depending on your ceiling composition)
- Jigsaw blade HCS, T 101 AO
- Wood drill bit (2.5 mm)
- 1 board, e.g. spruce (1,000 x 200 x 180 mm) (l x w x h)
- 4 wire cables (length as needed)
- 8 cable clamps to fit the wire cables
- 4 ceiling hooks with matching wall plugs (depending on your ceiling composition)
- 6 herb pots (upper diameter approx. 12 cm)
Let's start - step by step
Step 1: Saw the board
What you need: jigsaw, Compass, 1 board, e.g. spruce (1,000 x 200 x 180 mm) (l x w x h)
Let’s get started!
Before fresh herbs can swing above your head in the kitchen, you need to cut down the board that will hold your herb pots to the right size. A metre-long board will accommodate around six herb pots. If you don’t want to saw the board yourself, you can have your local DIY store do it for you. Once your board is the right length, use a compass to draw the outlines of the pot holes. The diameter of the holes should be around 1 cm smaller than the upper lip of the pots.
Step 2: Make 10 holes for the herb pots
What you need: Cordless drill/driver, Wood drill bit (2.5 mm), Wood drill bit (18 mm)
You need to drill a hole in each corner of the board so that you can hang the herb rack later on. To do this, insert a 2.5 mm wood drill bit into the cordless drill/driver and drill through the first corner of the board around 2 cm from the edge of the board, applying moderate pressure. We recommend marking the drill holes before you start. Once you’ve drilled a hole in each corner, swap the 2.5 mm wood drill bit for the 18 mm wood drill bit. Use this to drill a hole in each circle you drew for the pots, following the inner edge of the compass line. You’ll need these holes to saw out the circles later and transform your board into a herb rack.
Lay the wooden board on a workbench or other stable, raised surface. If you don’t have a way of clamping the board down, ask someone to hold the board firmly against your work surface. The aim is to make sure the board doesn’t slip. Make sure your helper’s hands are a safe distance from where you are drilling. Hold the cordless drill/driver firmly with both hands and drill through the wood using moderate pressure.
Step 3: Now if the pot has a hole in it ...
What you need: jigsaw, Jigsaw blade HCS, T 101 AO
Good news: round holes are much easier to saw than you might think! You’ve already completed the first step by drawing the circles for the pots and pre-drilling the holes. Now place a jigsaw into the pre-drilled holes and saw up to the edge of the hole, then continue around the edge of the compass circle. Make sure to keep your hand directly above the saw blade, as this will help you to saw more easily and precisely.
Step 4: Rounding things off nicely: sand the edges of the sawn holes
To ensure your herb pots don’t get scratched and to avoid splinters, you need to sand the edges of the holes you’ve sawn. For perfect results, sand the holes evenly without applying pressure, moving in one direction. To avoid getting sawdust in your eyes, we recommend wearing protective goggles.
Step 5: Hang the herb rack from the ceiling
What you need: Cordless drill/driver, Drill bits for mounting the rack (depending on your ceiling composition) , ceiling hooks, wall plugs, wire cable, cable clamps
To hang the herb rack from the ceiling, you need to drill four holes in the ceiling. The holes should line up with the holes you drilled into the corners of the board. Then, insert the wall plugs and screw in the ceiling hooks. Next, cut the wire cable to the desired length, thread the ends of the cables through the holes in the board, and fasten them with four cable clamps so that the rack hangs securely. Now thread the cables through the ceiling hooks and secure them with the last four clamps. Your herb-rack creation is now complete! Now you can plant it with your choice of basil, rosemary, mint or other herbs.
Choosing the right drill bit for your ceiling depends on the type of ceiling you have. If you don’t know whether you have a concrete, wood or plaster ceiling, it’s easy to find out. Knock on the ceiling with your hand or a hammer. Do you hear a hollow sound? If so, your ceiling is probably made from plasterboard, aerated concrete or wood. Is the sound dull or muffled? This means your ceiling is a solid one made from natural stone or concrete. Ask your DIY store which drill bit is best for your ceiling. If you’re unsure, you can perform a small test using a thin drill bit in a concealed area of the ceiling. Aside from the drill bit, you may also need to choose a different power tool depending on your ceiling composition. For soft materials, you can simply use your cordless drill/driver. If your ceiling is made from concrete or natural stone, we recommend using an impact drill.
Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.