Cookie Information

This website uses cookies for reasons of functionality, comfort, and statistics. You can change those settings at any time in the footer on "Privacy Settings". Our Privacy Policy
See less

Practical and organised: the DIY wooden shelving unit for your child’s bedroom

Share on Pinterest Share via email Print
A boltless shelving unit with boxes. There are figures, soft toys and a basketball on the shelves. A tepee is located to the left of the shelf, a marble run and soft toys to the right
Neatness meets niceness – with the DIY wooden shelving unit for your child’s bedroom
  • Difficulty
    medium
  • Costs
    50-100 £
  • Duration
    1-3 h

Introduction

Is your child’s bedroom a sea of chaos? If you have children then you’ll definitely be familiar with the sight of soft toys, games pieces and books covering every square inch of the floor. However, creating a tidy room couldn’t be easier! We’ll show you how to build a wooden shelving unit for your child’s bedroom complete with practical boxes so even the little things can be securely stowed away.

What you need

Icon my-product
Tools
Icon accessories
Additional items
  • ear protectors
  • protective goggles
  • work gloves
  • pencil
  • ruler
  • Triangle
  • drilling adapter for the cordless screwdriver
  • screw clamps
Icon confirmation
Material list
  • - Seven boards (e.g., bamboo boards): 122.5 x 40 x 2 cm (2x), 140 x 40 x 2 cm (2x) and 145 x 40 x 2 cm (3x).
  • Three to five chipboard panels: 38 x 28 x 0.5 cm
  • 21–35 screws: 3.5 x 25 mm
L: Length, W: Width, H: Height, D: Diameter

Let's start - step by step

1 4

Mark out the cross lap joints on

A pencil, a pocket rule and an angle measurer can be seen lying on a wooden board. Two cutting edges have been marked on the wooden board in pencil.
Mark out the cross lap joints on your wooden boards using an angle measurer
Diagram

What you need: pencil, Triangle, ruler

Pick up boards that have been cut to the right length from a timber yard. Alternatively, you can also cut them to size yourself. To build your wooden shelving unit, you’ll need seven wooden boards with the following dimensions: 122.5 x 40 x 2 cm (2x), 140 x 40 x 2 cm (2x) and 145 x 40 x 2 cm (3x). Mark out the cross laps on your boards. You can use the diagram above as a template. A cross lap joint is a traditional craftsman’s technique of joining pieces of wood together without the need for additional materials such as nails, screws or dowels. The cross lap joints used here join two pieces of wood together at a right angle so that half of each board sticks out.

2 4

Saw the joints for the cross laps

Close-up of a gloved hand sanding the edges of a wooden board with sandpaper.
Sand the edges with sandpaper

What you need: jigsaw, protective goggles, work gloves

Put on protective goggles, ear protection and suitable gloves before you start sawing. Now, use a jigsaw to cut out the U-shaped joints for the cross laps. Start by sawing vertically along the long lines. For the final, small piece, position the saw close enough so that you have room to saw horizontally.

3 4

Join the boards together

A man is joining the shelving boards together. One board is lying on the floor and is serving as a base to stabilise the boards for the shelves.
Now it’s time to put your wooden shelving unit together. To do so, join the horizontal boards that will serve as the shelves to the vertical boards

Tip: Make sure the boards are facing the right way as taking the boards apart later could prove difficult once they are firmly connected. Start with the bottom board. Use one of the boards that have been cut to length as a base to hold everything together (see the board on the floor on the left in the picture).

4 4

Attach back panels

Close-up of a hand using a cordless screwdriver to drill screws into a chipboard
You can attach back panels to your DIY wooden shelving unit to give it added stability

What you need: drilling adapter for the cordless screwdriver , three to five chipboards. 38 x 28 x 0.5 cm, 21–35 screws: 3.5 x 25 mm

Attach the back panels to secure and stabilise your shelving unit. It’s up to you how many you install. We recommend three to five back panels. You will need chipboard panels that are 38 x 28 x 0.5 cm in dimension. Attach the panels to the back side of your wooden shelving unit using a cordless screwdriver with a drilling adapter and a sufficient number of screws (3.5 x 25 mm) to keep them in place. Tip: If you install the panels diagonally next to each another, you will have to remove a corner. That’s why we recommend that you always leave a panel free. Your DIY wooden shelving unit for your kid’s bedroom is now ready! Tidying up is now child’s play with the right storage boxes.


Legal notice

Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.