Costs< 50 £
Duration< 1 h
Copper is the decor trend for 2018! Pieces made from this wonderfully shiny material will add a touch of refinement to your home. How about a copper clothes rail for your bedroom or hallway? It offers the perfect opportunity for you to show off your favourite clothes with style – and is easy to make thanks to our easy-peasy tutorial.
What you need
- ear protectors
- face mask
- tape measure
- protective goggles
- work gloves
- screw clamps
- small spatula
- copper cleaning agent, e.g. acetone or metal cleaner
- 2 towels to clean the pipes and remove the adhesive
- felt-tip pen
- 1 copper pipe: 250 x 2.2 cm (L x D)
- 3 copper pipes: 100 x 2.2 cm (L x D)
- 4 copper elbow fittings
- 2 copper tee fittings
- 2 copper end pieces
- Two-component adhesive
Let's start - step by step
Measure out the copper pipes
What you need: felt-tip pen, tape measure, copper pipes
Your new copper clothes rail will naturally need to be big enough to hold all of your clothes. With this in mind, measure out the following lengths of copper pipe ready for sawing:
- 2 x 120 cm
- 2 x 100 cm
- 4 x 25 cm
Mark these lengths with a thin felt-tip pen so that your marking stays legible on the metal.
Saw down the copper pipes
Once you've marked out your measurements, it's time to saw the pipes. We recommend that you secure the pipes to your work surface using screw clamps to keep them still while you saw. Make sure you protect yourself with work gloves, safety goggles and ear defenders.
Sand down and clean the ends of the copper pipes
What you need: Hand sanding paper for metal (240-grit), work gloves, copper cleaning agent, e.g. acetone or metal cleaner, towel
After sawing, copper pipes can be very sharp and develop ridges. You therefore need to sand down the sawn ends thoroughly with 240-grit sanding paper, which is suitable for metal. When doing this, make sure to wear your work gloves.
Then clean the metal using a copper cleaning agent and a towel. This will bring out the material's natural shine and will remove any residues that could react with the adhesive.
Assemble and glue together the base of the clothes rail
What you need: small spatula, 2 towels to clean the pipes and remove the adhesive, 4 copper pipes: 25 x 2.2 cm, 1 copper pipe: 100 x 2.2 cm, 2 elbow fittings, 2 tee fittings
Now you can begin assembling your clothes rail. For the base of your copper clothes rail, attach an elbow fitting to each end of a metre-long piece of copper pipe. Before you do this, apply some two-component adhesive to the fittings with a small spatula, then press them together. Turn the pipes until you feel a stop – this means they're properly secured. Remove any excess adhesive with a towel.
Caution: the adhesive will dry quickly, so you'll have to work swiftly!
Assemble the remaining pieces as follows: connect the short pipes with a tee fitting with the opening facing upwards. This will give you pipes that measure around 50 cm long. Then attach these to the elbow fittings using adhesive. Finally, attach the remaining end pieces to each of the shorter pipes.
Finish assembling the clothes rail
What you need: two-component adhesive, 2 copper pipes: 120 x 2.2 cm, 1 copper pipe: 100 x 2.2 cm, 2 elbow fittings
Connect the second metre-long pipe to the remaining elbow fittings – this is where the clothes will hang. Then attach the long 120-cm copper pipes one after the other into the tee fitting in the base. Again, apply some two-component adhesive to the ends and inside the fittings to make sure your clothes rail is sturdy. Now add the top of the clothes rail – again applying adhesive for an extra-secure hold. Your new home accessory for the bedroom or hallway is now finished!
Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.