Cookie Information

This website uses cookies for reasons of functionality, comfort, and statistics. You can change those settings at any time in the footer on "Privacy Settings". Our Privacy Policy
See less

A modern room partition: a miracle cure for any small living room

Share on Pinterest Share via email Print
A room partition is standing between a kitchen area and a home office in an elongated room.
This transparent partition creates structure without causing the room to lose its depth.
  • Difficulty
    medium
  • Costs
    < 50 €
  • Duration
    1-3 h

Introduction

Do you need another room? Are you unhappy with the floorplan in your home? Then you need a room partition. We’ll show you how to build your own elegant wooden partition in a few simple steps. Our model is foldable and blends seamlessly into any ambience thanks to its transparency and sleek, black aesthetic.

What you need

Icon accessories
Additional items
  • Ruler
  • Paint roller
  • G-clamps
  • Pencil
Icon confirmation
Material list
  • Squared timber made from spruce with a cross-sectional area of 34 x 54 mm: Four with a length of 2,400 mm (or longer, depending on ceiling height), four with a length of 1,250 mm
  • Profiles made from spruce with a cross-sectional area of 23 x 23 mm: Two with a length of 2,400 mm (or longer, depending on ceiling height), four with a length of 1,180 mm
  • Two hinges
  • 28 black screws (4.2 x 70 mm)
  • 12 screws (4 x 30 mm)
  • Black wood paint
L: Length, W: Width, H: Height, D: Diameter

Let's start - step by step

1 6

Saw and sand the wooden slats

Close-up of a man sanding the edge of a piece of wood with a sander.
Saw the edges to the required dimensions. Then, sand the edges.

For this partition, you’ll need to saw the squared timbers to two different lengths. We recommend asking staff at your local DIY store to cut these to the required lengths for you.[nk1] Then, sand all the edges and rough points – paying particular attention to the sawn edges – with the YOUseries Sander. If you like, you can use the YOUseries Vac together with the Dust Extractor to avoid sawdust making a mess.

2 6

Prepare the screw holes for the frame

Close up of a man drilling a hole in a wooden slat.
Drill holes for the screws in the wooden slats.

What you need: YOUseries Drill, countersink bit, drill bit 4 mm (YOUseries), G-clamps, Ruler, Pencil

It’s now time to drill holes at the points where the screws will be inserted later. However, before you begin drilling, we recommend that you arrange the wooden slats on the floor of a large room corresponding to their final, assembled position so that you keep track of what you have done.

Start with the squared timbers – they will form the frame of the room partition. Take the shorter squared timbers, lie them on their wider side and drill two holes at the same height at both ends of each of them. These holes should be 170 mm away from the bottom edge and 150 mm from their respective side edges. Use a size-4 drill bit.

You should adjust the drilled holes with a countersink so that the heads of the screws don’t stick out. Do this by switching the wood drill bit for a countersink and using it to slightly widen the holes so that the screw head sits flush with the surrounding material. Make sure that you use the countersink on the correct side of the drill hole so that the heads of the screws are on the outside after you have assembled your room partition.

Icon hint
Tip

Mark the positions for the holes before you start with a pencil and a ruler and secure the wood with G-clamps so that it doesn’t slip while you’re drilling.

3 6

Prepare the screw holes for the inner slats

Close-up of a man marking positions on two wooden slats using a ruler and a pencil.
Close-up of a man drilling holes for countersinks with a cordless drill.

What you need: YOUseries Drill, countersink bit, G-clamps

The next step is to mark the positions for the drill holes where the inner wooden slats are going to be screwed in later. This is important for making sure the vertical and horizontal slats move past each other cleanly. Take hold of the shorter squared timbers once again and mark a position in the middle (625 mm) that is 150 mm away from either side edge. Make sure that the positions on the short squared timbers will be directly opposite one another once you put the frame together.

Then, mark the positions for the drill holes for the two horizontal slats on the longer squared timbers. They should be 600 mm and 1,200 mm in height at a length of 2,400 mm. The drill holes should again be 150 mm away from one of the two side edges. If you have chosen the front side edge for the vertical slats, then choose the back side edge for the horizontal slats. You should again widen the drilled holes with a countersink .

4 6

Paint the squared timbers black

Close-up of a man applying black paint to several squared timbers with a paint roller.
Paint all four sides of the wooden slats black.

What you need: Paint roller, black wood paint

Now apply black wood paint to all four sides of the wooden slats. Leave each side long enough to dry before you move on to the next one.

5 6

Screw everything together

Close-up of a man securing a wooden slat with a cordless screwdriver.
The frame is taking shape: it’s time to screw all the wooden slats together.

What you need: YOUseries Drill, YOUseries Bit and Drill Set, G-clamps, 28 black screws (4.2 x 70 mm)

Now that all the preparations are complete, it’s time to start using the YOUseries Drill. You should countersink 14 screws in every frame, otherwise you have missed a drill hole somewhere.

6 6

Attach the hinges

Close-up of a man securing a hinge to a wooden slat with a cordless screwdriver.
Screw on the hinges.

What you need: YOUseries Drill, YOUseries Bit and Drill Set, G-clamps, two hinges, 12 screws (4 x 30 mm)

Finally, connect the two halves of the room partition using two hinges. To do this, lie the two frames next to each other and line them up. To make sure its appearance is even, the bottom end of the bottom hinge should be 66 cm away from the floor and the top end of the top hinge should be 660 mm away from the top end of the room partition. Each hinge requires six small screws.

There is probably going to be a lot of sawdust swirling around your living room once you’re finished with this project. The YOUseries Vac will make it all disappear in no time at all.

Icon hint
Tip

You can decorate your room partition, for example, by screwing a small hook into the wood underneath the top and hanging plants or other decorative items on it. This will also make the partition less transparent.


Legal notice

Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.