Cookie Information

This website uses cookies for reasons of functionality, comfort, and statistics. You can change those settings at any time in the footer on "Privacy Settings". Our Privacy Policy
See less

Creative and stylish baby gym

Share on Pinterest Share via email Print
An image of a homemade yellow wooden baby house
A cosy little house for little explorers!
  • Difficulty
    medium
  • Costs
    100-200 £
  • Duration
    3-8 h

Introduction

A cosy little house for little explorers! With colourful toys suspended from the roof for the baby to look at and touch, this homemade “Baby Gym” is a cuddly place for your little one. As soon as babies are a few months old, they want to explore and touch their environment – looking at colours and grabbing shapes is particularly exciting for them. Homemade and decorated with love, this little house is a really special place to discover the world.

What you need

Icon accessories
Additional items
  • face mask
  • floor protector or cover sheets
  • protective goggles
  • scraper
  • Protective gloves
Icon confirmation
Material list
  • 8 rectangular wooden strips, 1.5 m long, (38 x 38 mm)
  • 1 wooden board, 2.5 m long, (18 x 200 mm)
  • 50 wood screws, galvanised (4.0 x 80 mm)
  • Approx. 0.7 l paint, suitable for infants (EN 71-3 standard)
  • wood filler
L: Length, W: Width, H: Height, D: Diameter

Let's start - step by step

1 6

Cut the wood to size

An image of all the tools and materials needed to make a wooden baby home
Here's everything you need

What you need: mini-saw, screw clamps, protective goggles, tape measure, wooden planks

First you need to shorten all the strips to the right length as specified in the construction plan: Cut four cross struts for the side sections and four corner struts (“A1” in the construction plan), four cross struts for the front and back sections (“A2” in the construction plan) and a gable strip (“A3” in the construction plan) to a length of 70 cm each. Then shorten two of the roof strips to 50 cm (“B” in the construction plan) and the other two to 46.2 cm (“C” in the construction plan). Now adapt all four roof strips to the angle of the roof slope. To do so, bevel the bottom edges of each roof strip to 45 degrees so that they can be placed against each other in a right angle at the top. A suitable tool is a mini-saw or jigsaw. After sawing, carefully sand down the edges so that they are nice and smooth.

Construction PlanDownload
2 6

Pre-drill the holes

What you need: Cordless drill/driver with matching bit, screw clamps

Next, pre-drill the cut side strips and corner struts (“A1” in the construction plan) for the frames of the side sections according to the marks in the construction plan, using a cordless drill driver and a 3mm wood drill bit so that the screws can be driven in flush later on. Now put together the side and corner struts (“A1” in the construction plan) and fit them together with screws. Connect the two resulting frames to each other by means of the four cross struts (“A2” in the construction plan) at both the top and bottom to produce a cube. When doing so, again use the wood drill bit to pre-drill the holes.

3 6

Make the roof

Someone using a cordless drill/driver to fix the roof together for the house
Time to make the roof

What good is a house with no roof? That’s why we’re going to make one now. Put two of each roof strip (“B” and “C” in the construction plan) at a right angle to each other as shown in the construction plan, pre-drill and fit them together with screws so that the longer of the two strips is on top. The previously bevelled ends of the strips will form the bottom edges that are later placed on the frame of the house. Then connect the two sides of the roof at the tips with screws using the gable strip (“A3” in the construction plan). Now place the finished roof on the frame and pre-drill and fit it with screws according to the marks in the construction plan – the screws have to be thoroughly countersunk here as well.

4 6

Create the back panels

Someone using a cordless drill/driver to create the side panels for the house
Attatch the side panels to the house

To ensure that the baby cannot roll out of the side and that the little house is nice and stable, it is now panelled with three wooden boards (“D” in the construction plan). To do so, cut the wooden board using a cordless mini-saw so that one board on each side (62.4 cm length) and one on the back (70 cm length) of the house can be fitted into the frames. Insert the sawn wooden boards and fit them to the frame by driving in two screws on each side from the outside. Before doing so, again use the wood drill bit to pre-drill all holes on each side from the outside according to the marks in the construction plan.

5 6

Make the house safe

What you need: scraper, wood filler

To make everything look better and to increase safety for the baby, seal all screw holes flat with wood filler. Once the filler has dried, thoroughly sand down the filled positions again.

6 6

Add the finishing touches

Someone using a paint spray system to add the finishing touches to the house
Just add paint

What you need: paint spray system, floor protector or cover sheets, face mask, paint

Once the surfaces are smooth and splinter-free, you can spray the baby house in your favourite colour. Use a paint spray system which enables paint to be applied quickly and evenly. Important: Use paint that is suitable for infants and meets the EN 71-3 standard. To work precisely, set the spray jet to “pencil jet” and hold the gun about 20 to 25 cm away from the little house. Leave it to dry for several hours, ideally overnight. Then furnish the house with a soft pillow or blanket, add your little one’s favourite cuddly toys and hang up colourful rattles and toys – and your baby’s cuddly paradise is finished!


Legal notice

Bosch does not accept any responsibility for the instructions stored here. Bosch would also like to point out that you follow these instructions at your own risk. For your own safety, please take all the necessary precautions.